FIG. A communications link also will exist to the meter, outside services and other equipment.As a distributed system, the functions are divided between the two unit types.
Contact closures 51 will be used to control these units. This centralized computing power will also allow for strategized cost control. The system can decide, based on the indoor humidity level reported by the humidifier through function 15, to use the humidifier to increase the humidity to improve the affect of heating the premise. NASA Images Solar System Collection Ames Research Center. This feature is defeated if the system is placed in the off position, but will be overridden if the user elects to activate the temperature alarm mode capability of the system.33. ranging from initial design to machined castings....cmw operates in three primary business units: electrical contacts, tungsten-based high-density metals and copper-based resistance welding consumables....riverside brass is a respected leader and innovator among ontario's non-ferrous foundries, providing advanced capabilities in brass, bronze and aluminum casting....gateway sales corporation specializes in sintered metal parts, metal injection molding, powdered forged parts, fasteners and extrusions. 2. The weather parameters or index will be used in at least the two following ways: as a load variable which would modify the estimate of the amount of energy required, time and cost to heat or cool the premise from a specific temperature to a new set point and as a predictor for user-desired temperature set point changes.In addition to reading energy meters of various types of energy, function 11 will read consumption data collected by submetering devices.
Historical totals of energy units usage and cost for this month, last 14 months and year to date.13. For example, if the user enters the key sequence to begin entering cost information, then the user will be prompted for supplier ID, rates, start time for each rate, length of time the rate is valid, fees, the HVAC consumption in kilowatts and the correct time, day, date and 12 or 24 hour format, for examples.For temperature data, the user will be prompted for set point, set point control on or off, dead-band or high/low mode, high and low values for the selected mode, temperature set point learning on 1, on 2, off or forget, alarm on or off, alarm high and low thresholds, temperature limiting on or off, high and low limit values, Centigrade or Fahrenheit temperature degree units and password protection on or off, for examples.For comfort data, the user will be prompted for ramping on or off, preconditioning on or off, rate of change for ramping and preconditioning (at fixed intervals in minutes per degree or learned), maximum cost at set point, maximum cost at high value, maximum cost at low value, high value cost over limit hold or shutdown and low value cost limit hold or shutdown, for examples.Certain data is not required under certain conditions such as the supplier ID when only one supplier can be entered. our manufacturing process is designed to be flexible, to conform to your just-in-time inventory needs.
It includes a plurality of local load controlling processors. alliance calibration is located in cincinnati, oh. FIG. Humidifiers and dehumidifiers can be controlled to enhance cooling or heating cycles where a cost savings can be calculated. ...sterling sintered technologies-a 45 year old custom service we have grown over the past 50 years to become one of north americaís largest manufacturers of carbon-steel and steel-alloy forgings...since 1928, schutte-buffalo hammermill has been doing it all. For credit accounts, charges will be calculated and displayed through function 43 to the user for each billing cycle and a estimated bill for the present billing cycle will be provided on an on going and forward projecting basis. In the absence of cost and energy consumption control input parameters, the system will maintain environmental conditions within user-defined comfort ranges. An indoor environmental condition input receives a sensed indoor environmental condition. To illustrate this point, water may be heated in a dual fuel water heater using either gas or electricity as a direct energy unit source.
This input is passed to function 21 for permanent storage.Input function 15 provides for interfacing with sensors and equipment as well any other data sources that may be appropriate such as a Smart Card 9 or communication link 6.
Contact closures 51 will be used to control these units. This centralized computing power will also allow for strategized cost control. The system can decide, based on the indoor humidity level reported by the humidifier through function 15, to use the humidifier to increase the humidity to improve the affect of heating the premise. NASA Images Solar System Collection Ames Research Center. This feature is defeated if the system is placed in the off position, but will be overridden if the user elects to activate the temperature alarm mode capability of the system.33. ranging from initial design to machined castings....cmw operates in three primary business units: electrical contacts, tungsten-based high-density metals and copper-based resistance welding consumables....riverside brass is a respected leader and innovator among ontario's non-ferrous foundries, providing advanced capabilities in brass, bronze and aluminum casting....gateway sales corporation specializes in sintered metal parts, metal injection molding, powdered forged parts, fasteners and extrusions. 2. The weather parameters or index will be used in at least the two following ways: as a load variable which would modify the estimate of the amount of energy required, time and cost to heat or cool the premise from a specific temperature to a new set point and as a predictor for user-desired temperature set point changes.In addition to reading energy meters of various types of energy, function 11 will read consumption data collected by submetering devices.
Historical totals of energy units usage and cost for this month, last 14 months and year to date.13. For example, if the user enters the key sequence to begin entering cost information, then the user will be prompted for supplier ID, rates, start time for each rate, length of time the rate is valid, fees, the HVAC consumption in kilowatts and the correct time, day, date and 12 or 24 hour format, for examples.For temperature data, the user will be prompted for set point, set point control on or off, dead-band or high/low mode, high and low values for the selected mode, temperature set point learning on 1, on 2, off or forget, alarm on or off, alarm high and low thresholds, temperature limiting on or off, high and low limit values, Centigrade or Fahrenheit temperature degree units and password protection on or off, for examples.For comfort data, the user will be prompted for ramping on or off, preconditioning on or off, rate of change for ramping and preconditioning (at fixed intervals in minutes per degree or learned), maximum cost at set point, maximum cost at high value, maximum cost at low value, high value cost over limit hold or shutdown and low value cost limit hold or shutdown, for examples.Certain data is not required under certain conditions such as the supplier ID when only one supplier can be entered. our manufacturing process is designed to be flexible, to conform to your just-in-time inventory needs.
It includes a plurality of local load controlling processors. alliance calibration is located in cincinnati, oh. FIG. Humidifiers and dehumidifiers can be controlled to enhance cooling or heating cycles where a cost savings can be calculated. ...sterling sintered technologies-a 45 year old custom service we have grown over the past 50 years to become one of north americaís largest manufacturers of carbon-steel and steel-alloy forgings...since 1928, schutte-buffalo hammermill has been doing it all. For credit accounts, charges will be calculated and displayed through function 43 to the user for each billing cycle and a estimated bill for the present billing cycle will be provided on an on going and forward projecting basis. In the absence of cost and energy consumption control input parameters, the system will maintain environmental conditions within user-defined comfort ranges. An indoor environmental condition input receives a sensed indoor environmental condition. To illustrate this point, water may be heated in a dual fuel water heater using either gas or electricity as a direct energy unit source.
This input is passed to function 21 for permanent storage.Input function 15 provides for interfacing with sensors and equipment as well any other data sources that may be appropriate such as a Smart Card 9 or communication link 6.